Virtual Ethernet device

2007-01-26T11:07:25Z

Pask: /* Adding veth to a VE */

'''Virtual ethernet device''' is an ethernet-like device which can be used inside a [[VE]]. Unlike
[[venet]] network device, veth device has a MAC address. Due to this, it can be used in configurations, when veth is bridged to ethX or other device and VE user fully sets up his networking himself,
including IPs, gateways etc.

Virtual ethernet device consist of two ethernet devices - one in [[VE0]] and another one
in VE. These devices are connected to each other, so if a packet goes to one
device it will come out from the other device.

== Virtual ethernet device usage ==

=== Kernel module ===
First of all, make sure the <code>vzethdev</code> module is loaded:
<pre>
# lsmod | grep vzeth
vzethdev 8224 0
vzmon 35164 5 vzethdev,vznetdev,vzrst,vzcpt
vzdev 3080 4 vzethdev,vznetdev,vzmon,vzdquota
</pre>

In case it is not loaded, load it:
<pre>
# modprobe vzethdev
</pre>

You might want to add the module to <code>/etc/init.d/vz script</code>, so it will be loaded during startup.

=== Adding veth to a VE ===
<pre>
vzctl set <VEID> --veth_add <dev_name>,<dev_addr>,<ve_dev_name>,<ve_dev_addr>
</pre>
Here
* <tt>dev_name</tt> is the ethernet device name that you are creating on the [[VE0|host system]]
* <tt>dev_addr</tt> is its MAC address
* <tt>ve_dev_name</tt> is the corresponding ethernet device name you are creating on the VE
* <tt>ve_dev_addr</tt> is its MAC address

MAC addresses must be entered in XX:XX:XX:XX:XX:XX format. Note that this option
is incremental, so devices are added to already existing ones.

NB there are no spaces after the commas

==== Examples ====
<pre>
vzctl set 101 --veth_add veth101.0,00:12:34:56:78:9A,eth0,00:12:34:56:78:9B --save
</pre>
After executing this command <tt>veth</tt> device will be created for VE 101 and veth configuration will be saved to a VE configuration file.
Host-side ethernet device will have <tt>veth101.0</tt> name and <tt>00:12:34:56:78:9A</tt> MAC address.
VE-side ethernet device will have <tt>eth0</tt> name and <tt>00:12:34:56:78:9B</tt> MAC address.
{{Note|Use random MAC addresses. Do not use MAC addresses of real eth devices, because this can lead to collisions.}}

Warning: sintax seems changed in (current) version vzctl-3.0.14. Actual sintax is:
==== Examples ====
<pre>
vzctl set 101 --netif_add eth0,00:12:34:56:78:9A,veth101.0,00:12:34:56:78:9B --save
</pre>

where eth0 is the interface being created in your Virtual Machine, while veth101.0 is being created in the host machine.

=== Removing veth from a VE ===
<pre>
vzctl set <VEID> --veth_del <dev_name>
</pre>
Here <tt>dev_name</tt> is the ethernet device name in the [[VE0|host system]].

==== Example ====
<pre>
vzctl set 101 --veth_del veth101.0 --save
</pre>
After executing this command veth device with host-side ethernet name veth101.0 will be removed from VE 101 and veth configuration will be updated in VE config file.

== Common configurations with virtual ethernet devices ==
Module <tt>vzethdev</tt> must be loaded to operate with veth devices.

=== Simple configuration with virtual ethernet device ===

==== Start a VE ====
<pre>
[host-node]# vzctl start 101
</pre>

==== Add veth device to VE ====
<pre>
[host-node]# vzctl set 101 --veth_add veth101.0,00:12:34:56:78:9A,eth0,00:12:34:56:78:9B --save
</pre>

==== Configure devices in VE0 ====
<pre>
[host-node]# ifconfig veth101.0 0
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/veth101.0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/veth101.0/proxy_arp
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/eth0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp
</pre>

==== Configure device in VE ====
<pre>
[host-node]# vzctl enter 101
[ve-101]# /sbin/ifconfig eth0 0
[ve-101]# /sbin/ip addr add 192.168.0.101 dev eth0
[ve-101]# /sbin/ip route add default dev eth0
</pre>

==== Add route in [[VE0]] ====
<pre>
[host-node]# ip route add 192.168.0.101 dev veth101.0
</pre>

=== Virtual ethernet device with IPv6 ===

==== Start [[VE]] ====
<pre>
[host-node]# vzctl start 101
</pre>

==== Add veth device to [[VE]] ====
<pre>
[host-node]# vzctl set 101 --veth_add veth101.0,00:12:34:56:78:9A,eth0,00:12:34:56:78:9B --save
</pre>

==== Configure devices in [[VE0]] ====
<pre>
[host-node]# ifconfig veth101.0 0
[host-node]# echo 1 > /proc/sys/net/ipv6/conf/veth101.0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv6/conf/eth0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv6/conf/all/forwarding
</pre>

==== Configure device in [[VE]] ====
<pre>
[host-node]# vzctl enter 101
[ve-101]# /sbin/ifconfig eth0 0
</pre>

==== Start router advertisement daemon (radvd) for IPv6 in VE0 ====
First you need to edit radvd configuration file. Here is a simple example of <tt>/etc/radv.conf</tt>:
<pre>
interface veth101.0
{
AdvSendAdvert on;
MinRtrAdvInterval 3;
MaxRtrAdvInterval 10;
AdvHomeAgentFlag off;

prefix 3ffe:2400:0:0::/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;
};
};

interface eth0
{
AdvSendAdvert on;
MinRtrAdvInterval 3;
MaxRtrAdvInterval 10;
AdvHomeAgentFlag off;

prefix 3ffe:0302:0011:0002::/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;
};
};
</pre>

Then, start radvd:
<pre>
[host-node]# /etc/init.d/radvd start
</pre>

==== Add IPv6 addresses to devices in [[VE0]] ====
<pre>
[host-node]# ip addr add dev veth101.0 3ffe:2400::212:34ff:fe56:789a/64
[host-node]# ip addr add dev eth0 3ffe:0302:0011:0002:211:22ff:fe33:4455/64
</pre>

=== Virtual ethernet devices can be joined in one bridge ===
Perform steps 1 - 4 from Simple configuration chapter for several VEs and/or veth devices

==== Create bridge device ====
<pre>
[host-node]# brctl addbr vzbr0
</pre>

==== Add veth devices to bridge ====
<pre>
[host-node]# brctl addif vzbr0 veth101.0
...
[host-node]# brctl addif vzbr0 veth101.n
[host-node]# brctl addif vzbr0 veth102.0
...
...
[host-node]# brctl addif vzbr0 vethXXX.N
</pre>

==== Configure bridge device ====
<pre>
[host-node]# ifconfig vzbr0 0
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/vzbr0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/vzbr0/proxy_arp
</pre>

==== Add routes in [[VE0]] ====
<pre>
[host-node]# ip route add 192.168.101.1 dev vzbr0
...
[host-node]# ip route add 192.168.101.n dev vzbr0
[host-node]# ip route add 192.168.102.1 dev vzbr0
...
...
[host-node]# ip route add 192.168.XXX.N dev vzbr0
</pre>

Thus you'll have more convinient configuration, i.e. all routes to VEs will be through this bridge and VEs can communicate with each other even without these routes.

=== Virtual ethernet devices + VLAN ===
This configuration can be done by adding vlan device to the previous configuration.

== See also ==
* [[Virtual network device]]
* [[Differences between venet and veth]]

== External links ==
* [http://www.tldp.org/HOWTO/Linux+IPv6-HOWTO/hints-daemons-radvd.html Linux IPv6 HOWTO, a chapter about radvd]

[[Category: Networking]]
[[Category: HOWTO]]

OpenVZ Virtuozzo Containers Wiki - User contributions [en]

Virtual Ethernet device