Editing Using private IPs for Hardware Nodes

{{Legacy}}

This article describes how to assign public IPs to containers running on OVZ Hardware Nodes in case you have a following network topology:

[[Image:PrivateIPs_fig1.gif|An initial network topology]]

== Using a spare IP in the same range ==
If you have a spare IP to use, you could assign this as a subinterface and use this as nameserver:

<pre>[HN] ifconfig eth0:1 *.*.*.*
[HN] vzctl set 101 --nameserver *.*.*.*</pre>

== Prerequisites ==
This configuration was tested on a RHEL5 OpenVZ Hardware Node and a container based on a Fedora Core 5 template.
Other host OSs and templates might require some configuration changes, please add corresponding OS specific changes if you've faced any.

This article assumes the presence of 'brctl', 'ip' and 'ifconfig' utils. You may need to install missing packages like 'bridge-utils'/'iproute'/'net-tools' or others which contain those utilities.

This article assumes you have already [[Quick installation|installed OpenVZ]],
prepared the [[OS template cache]](s) and have
[[Basic_operations_in_OpenVZ_environment|container(s) created]]. If not, follow the links to perform the steps needed.
{{Note|don't assign an IP after container creation.}}

== An OVZ Hardware Node has the only one Ethernet interface ==
(assume eth0)

=== Hardware Node configuration ===

{{Warning|if you are '''configuring''' the node '''remotely''' you '''must''' prepare a '''script''' with the below commands and run it in background with the redirected output or you'll '''lose the access''' to the Node.}}

==== Create a bridge device ====
 [HN]# brctl addbr br0

==== Remove an IP from eth0 interface ====
 [HN]# ifconfig eth0 0

==== Add eth0 interface into the bridge ====
 [HN]# brctl addif br0 eth0
 
==== Assign the IP to the bridge ====
(the same that was assigned on eth0 earlier)
 [HN]# ifconfig br0 10.0.0.2/24

==== Resurrect the default routing ====
 [HN]# ip route add default via 10.0.0.1 dev br0
 


==== A script example ====
<pre>
[HN]# cat /tmp/br_add 
#!/bin/bash

brctl addbr br0
ifconfig eth0 0 
brctl addif br0 eth0 
ifconfig br0 10.0.0.2/24 
ip route add default via 10.0.0.1 dev br0
</pre>

 [HN]# /tmp/br_add >/dev/null 2>&1 &

Way to use the internet to help ppeloe solve problems!

=== Resulting OpenVZ Node configuration ===
[[Image:PrivateIPs_fig2.gif|Resulting OpenVZ Node configuration]]

=== Making the configuration persistent ===

==== Set up a bridge on a HN ====
This can be done by configuring the <code>ifcfg-*</code> files located in <code>/etc/sysconfig/network-scripts/</code>.

Assuming you had a configuration file (e.g. <code>ifcfg-eth0</code>) like:
<pre>
DEVICE=eth0
ONBOOT=yes
IPADDR=10.0.0.2
NETMASK=255.255.255.0
GATEWAY=10.0.0.1
</pre>

To automatically create bridge <code>br0</code>  you can create <code>ifcfg-br0</code>:
<pre>
DEVICE=br0
TYPE=Bridge
ONBOOT=yes
IPADDR=10.0.0.2
NETMASK=255.255.255.0
GATEWAY=10.0.0.1
</pre>

and edit <code>ifcfg-eth0</code> to add the <code>eth0</code> interface into the bridge <code>br0</code>:
<pre>
DEVICE=eth0
ONBOOT=yes
BRIDGE=br0
</pre>

==== Edit the container's configuration ====
Add these parameters to the <code>/etc/vz/conf/$CTID.conf</code> file which will be used during the network configuration:
* Add <code>VETH_IP_ADDRESS="IP/MASK"</code> (a container can have multiple IPs separated by spaces)
* Add <code>VE_DEFAULT_GATEWAY="CT DEFAULT GATEWAY"</code>
* Add <code>BRIDGEDEV="BRIDGE NAME"</code> (a bridge name to which the container veth interface should be added)

An example:
<pre>
# Network customization section
VETH_IP_ADDRESS="85.86.87.195/26"
VE_DEFAULT_GATEWAY="85.86.87.193"
BRIDGEDEV="br0"
</pre>

==== Create a custom network configuration script ====
which should be called each time a container is started (e.g. <code>/usr/sbin/vznetcfg.custom</code>):
<pre>
#!/bin/bash
# /usr/sbin/vznetcfg.custom
# a script to bring up bridged network interfaces (veth's) in a container

GLOBALCONFIGFILE=/etc/vz/vz.conf
CTCONFIGFILE=/etc/vz/conf/$VEID.conf
vzctl=/usr/sbin/vzctl
brctl=/usr/sbin/brctl
ip=/sbin/ip
ifconfig=/sbin/ifconfig
. $GLOBALCONFIGFILE
. $CTCONFIGFILE

NETIF_OPTIONS=`echo $NETIF | sed 's/,/\n/g'`
for str in $NETIF_OPTIONS; do \
        # getting 'ifname' parameter value
        if  echo "$str" | grep -o "^ifname=" ; then
                # remove the parameter name from the string (along with '=')
                CTIFNAME=${str#*=};
        fi
        # getting 'host_ifname' parameter value
        if  echo "$str" | grep -o "^host_ifname=" ; then
                # remove the parameter name from the string (along with '=')
                VZHOSTIF=${str#*=};
        fi
done

if [ ! -n "$VETH_IP_ADDRESS" ]; then
   echo "According to $CONFIGFILE CT$VEID has no veth IPs configured."
   exit 1
fi

if [ ! -n "$VZHOSTIF" ]; then
   echo "According to $CONFIGFILE CT$VEID has no veth interface configured."
   exit 1
fi

if [ ! -n "$CTIFNAME" ]; then
   echo "Corrupted $CONFIGFILE: no 'ifname' defined for host_ifname $VZHOSTIF."
   exit 1
fi

echo "Initializing interface $VZHOSTIF for CT$VEID."
$ifconfig $VZHOSTIF 0

CTROUTEDEV=$VZHOSTIF

if [ -n "$BRIDGEDEV" ]; then
   echo "Adding interface $VZHOSTIF to the bridge $BRIDGEDEV."
   CTROUTEDEV=$BRIDGEDEV
   $brctl addif $BRIDGEDEV $VZHOSTIF
fi

# Up the interface $CTIFNAME link in CT$VEID
$vzctl exec $VEID $ip link set $CTIFNAME up

for IP in $VETH_IP_ADDRESS; do
   echo "Adding an IP $IP to the $CTIFNAME for CT$VEID."
   $vzctl exec $VEID $ip address add $IP dev $CTIFNAME

   # removing the netmask
   IP_STRIP=${IP%%/*};

   echo "Adding a route from CT0 to CT$VEID using $IP_STRIP."
   $ip route add $IP_STRIP dev $CTROUTEDEV
done

if [ -n "$CT0_IP" ]; then
   echo "Adding a route from CT$VEID to CT0."
   $vzctl exec $VEID $ip route add $CT0_IP dev $CTIFNAME
fi

if [ -n "$VE_DEFAULT_GATEWAY" ]; then
   echo "Setting $VE_DEFAULT_GATEWAY as a default gateway for CT$VEID."
   $vzctl exec $VEID \
        $ip route add default via $VE_DEFAULT_GATEWAY dev $CTIFNAME
fi

exit 0
</pre>
<p><small>Note: this script can be easily extended to work for multiple triples &lt;bridge, ip address, veth device&gt;, see http://sysadmin-ivanov.blogspot.com/2008/02/2-veth-with-2-bridges-on-openvz-at.html </small></p>

==== Make the script to be run on a container start ====
In order to run above script on a container start create the file
<code>/etc/vz/vznet.conf</code> with the following contents:

 EXTERNAL_SCRIPT="/usr/sbin/vznetcfg.custom"

{{Note|<code>/usr/sbin/vznetcfg.custom</code> should be executable (chmod +x /usr/sbin/vznetcfg.custom)}}

{{Note|When CT is stoped there are HW → CT route(s) still present in route table. We can use On-umount script for solve this.}}

==== Create On-umount script for remove HW → CT route(s) ====
which should be called each time a container with VEID (<code>/etc/vz/conf/$VEID.umount</code>), or any container (<code>/etc/vz/conf/vps.umount</code>) is stopped.

<pre>
#!/bin/bash
# /etc/vz/conf/$VEID.umount or /etc/vz/conf/vps.umount
# a script to remove routes to container with veth-bridge from bridge 

CTCONFIGFILE=/etc/vz/conf/$VEID.conf
ip=/sbin/ip
. $CTCONFIGFILE

if [ ! -n "$VETH_IP_ADDRESS" ]; then
   exit 0
fi

if [ ! -n "$BRIDGEDEV" ]; then
   exit 0
fi

for IP in $VETH_IP_ADDRESS; do
   # removing the netmask
   IP_STRIP=${IP%%/*};
   
   echo "Remove a route from CT0 to CT$VEID using $IP_STRIP."
   $ip route del $IP_STRIP dev $BRIDGEDEV
done

exit 0
</pre>

{{Note|The script should be executable (chmod +x /etc/vz/conf/vps.umount)}}

==== Setting the route CT → HN ====
To set up a route from the CT to the HN, the custom script has to get a HN IP (the $CT0_IP variable in the script). There are several ways to specify it:

# Add an entry CT0_IP="CT0 IP" to the <code>$VEID.conf</code>
# Add an entry CT0_IP="CT0 IP" to the <code>/etc/vz/vz.conf</code> (the global configuration config file)
# Implement some smart algorithm to determine the CT0 IP right in the custom network configuration script

Each variant has its pros and cons, nevertheless for HN static IP configuration variant 2 seems to be acceptable (and the most simple).

== An OpenVZ Hardware Node has two Ethernet interfaces ==
Assuming you have 2 interfaces eth0 and eth1 and want to separate local traffic (10.0.0.0/24) from  external traffic.
Let's assign eth0 for the external traffic and eth1 for the local one.

If there is no need to make the container accessible from the HN and vice versa, it's enough to replace 'br0' with 'eth1' in the following steps of the above configuration:
* Hardware Node configuration → [[Using_private_IPs_for_Hardware_Nodes#Assign_the_IP_to_the_bridge|Assign the IP to the bridge]]
* Hardware Node configuration → [[Using_private_IPs_for_Hardware_Nodes#Resurrect_the_default_routing|Resurrect the default routing]]

It is nesessary to set a local IP for 'br0' to ensure CT ↔ HN connection availability.

== Putting containers to different subnetworks ==
It's enough to set up the correct $VETH_IP_ADDRESS and $VE_DEFAULT_GATEWAY values in the 
[[Using_private_IPs_for_Hardware_Nodes#Edit_the_container.27s_configuration|above configuration]].

== See also ==
* [[Virtual network device]]
* [[Differences between venet and veth]]

[[Category: HOWTO]]
[[Category: Networking]]
@@ Line 61: / Line 61: @@
   [HN]# /tmp/br_add >/dev/null 2>&1 &
-=== Container configuration ===
+Way to use the internet to help ppeloe solve problems!
-==== Start a container ====
- [HN]# vzctl start 101
-==== Add a [[Virtual_Ethernet_device|veth interface]] to the container ====
- [HN]# vzctl set 101 --netif_add eth0 --save
-==== Set up an IP to the newly created container's veth interface ====
- [HN]# vzctl exec 101 ifconfig eth0 85.86.87.195/26
-==== Add the container's veth interface to the bridge ====
- [HN]# brctl addif br0 veth101.0
-{{Note|There will be a delay of about 15 seconds(default for 2.6.18 kernel) while the bridge software runs STP to detect loops and transitions the veth interface to the forwarding state.
-<!-- /sys/class/net/$BR_NAME/bridge/forward_delay in SEC*USER_HZ -->}}
-==== Set up the default route for the container ====
- [HN]# vzctl exec 101 ip route add default via 85.86.87.193 dev eth0
-==== (Optional) Add CT↔HN routes ====
-The above configuration provides the following connections:
-* CT X ↔ CT Y (where CT X and CT Y can locate on any OVZ HN)
-* CT   ↔ Internet
-Note that
-* The accessability of the CT from the HN depends on the local gateway providing NAT (probably - yes)
-* The accessability of the HN from the CT depends on the ISP gateway being aware of the local network (probably not)
-So to provide CT ↔ HN accessibility despite the gateways' configuration you can add the following routes:
- [HN]# ip route add 85.86.87.195 dev br0
- [HN]# vzctl exec 101 ip route add 10.0.0.2 dev eth0
 === Resulting OpenVZ Node configuration ===