Virtual Ethernet device

Virtual ethernet device is ethernet device which can be used inside a VE. Unlike venet network device, veth device has a MAC address. Due to this, it can be used in configurations, when veth is bridged to ethX or other device and VPS user fully setups his networking himself, including IPs, gateways etc.

Virtual ethernet device consist of two ethernet devices - one in VE0 and another one in VE. These devices are connected to each other, so if a packet goes to one device it will come out from the other device.

Virtual ethernet device usage

Adding veth to a VE

vzctl set <VEID> --veth_add <dev_name>,<dev_addr>,<ve_dev_name>,<ve_dev_addr>

Here

• dev_name is ethernet device name in the host system
• dev_addr is its MAC address
• ve_dev_name is an ethernet device name in the VE
• ve_dev_addr is its MAC address

MAC addresses must be entered in XX:XX:XX:XX:XX:XX format. Note that this option is incremental, so devices are added to already existing ones.

Examples

vzctl set 101 --veth_add veth101.0,00:12:34:56:78:9A,eth0,00:12:34:56:78:9B --save

After executing this command veth device will be created for VE 101 and veth configuration will be saved to a VE configuration file. Host-side ethernet device will have veth101.0 name and 00:12:34:56:78:9A MAC address. VE-side ethernet device will have eth0 name and 00:12:34:56:78:9B MAC address.

Note: Use random MAC addresses. Do not use MAC addresses of real eth devices, beacuse this can lead to collisions.

Removing veth from a VE

vzctl set <VEID> --veth_del <dev_name>

Here dev_name is the ethernet device name in the host system.

Example

vzctl set 101 --veth_del veth101.0 --save

After executing this command veth device with host-side ethernet name veth101.0 will be removed from VE 101 and veth configuration will be updated in VE config file.

Common configurations with virtual ethernet devices

Module vzethdev must be loaded to operate with veth devices.

Simple configuration with virtual ethernet device

Start a VE

[host-node]# vzctl start 101

Add veth device to VE

[host-node]# vzctl set 101 --veth_add veth101.0,00:12:34:56:78:9A,eth0,00:12:34:56:78:9B --save

Configure devices in VE0

[host-node]# ifconfig veth101.0 0
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/veth101.0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/veth101.0/proxy_arp
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/eth0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp

Configure device in VE

[host-node]# vzctl enter 101
[ve-101]# /sbin/ifconfig eth0 0
[ve-101]# /sbin/ip addr add 192.168.0.101 dev eth0
[ve-101]# /sbin/ip route add default dev eth0

Add route in VE0

[host-node]# ip route add 192.168.0.101 dev veth101.0

Virtual ethernet device with IPv6

Start VE

[host-node]# vzctl start 101

Add veth device to VE

[host-node]# vzctl set 101 --veth_add veth101.0,00:12:34:56:78:9A,eth0,00:12:34:56:78:9B --save

Configure devices in VE0

[host-node]# ifconfig veth101.0 0
[host-node]# echo 1 > /proc/sys/net/ipv6/conf/veth101.0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv6/conf/eth0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv6/conf/all/forwarding

Configure device in VE

[host-node]# vzctl enter 101
[ve-101]# /sbin/ifconfig eth0 0

Start router advertisement daemon (radvd) for IPv6 in VE0

First you need to edit radvd configuration file. Here is a simple example of /etc/radv.conf:

interface veth101.0
{
        AdvSendAdvert on;
        MinRtrAdvInterval 3;
        MaxRtrAdvInterval 10;
        AdvHomeAgentFlag off;

        prefix 3ffe:2400:0:0::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
                AdvRouterAddr off;
        };
};

interface eth0
{
        AdvSendAdvert on;
        MinRtrAdvInterval 3;
        MaxRtrAdvInterval 10;
        AdvHomeAgentFlag off;

        prefix 3ffe:0302:0011:0002::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
                AdvRouterAddr off;
        };
};

Then, start radvd:

[host-node]# /etc/init.d/radvd start

Add IPv6 addresses to devices in VE0

[host-node]# ip addr add dev veth101.0 3ffe:2400::212:34ff:fe56:789a/64
[host-node]# ip addr add dev eth0 3ffe:0302:0011:0002:211:22ff:fe33:4455/64

Virtual ethernet devices can be joined in one bridge

Perform steps 1 - 4 from Simple configuration chapter for several VEs and/or veth devices

Create bridge device

[host-node]# brctl addbr vzbr0

Add veth devices to bridge

[host-node]# brctl addif vzbr0 veth101.0
...
[host-node]# brctl addif vzbr0 veth101.n
[host-node]# brctl addif vzbr0 veth102.0
...
...
[host-node]# brctl addif vzbr0 vethXXX.N

Configure bridge device

[host-node]# ifconfig vzbr0 0
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/vzbr0/forwarding
[host-node]# echo 1 > /proc/sys/net/ipv4/conf/vzbr0/proxy_arp

Add routes in VE0

[host-node]# ip route add 192.168.101.1 dev vzbr0
...
[host-node]# ip route add 192.168.101.n dev vzbr0
[host-node]# ip route add 192.168.102.1 dev vzbr0
...
...
[host-node]# ip route add 192.168.XXX.N dev vzbr0

Thus you'll have more convinient configuration, i.e. all routes to VEs will be through this bridge and VEs can communicate with each other even without these routes.

Virtual ethernet devices + VLAN

This configuration can be done by adding vlan device to the previous configuration.

External links

• Linux IPv6 HOWTO, a chapter about radvd