Ploop/Getting started

<translate> This article describes how to use container-in-a-file technology aka ploop

Requirements

The following is required for ploop to work:

1. RHEL6-based OpenVZ kernel, i.e. 042stabXXX.
2. /vz partition formatted as ext4 and mounted in ordered mode, or residing on NFSv3. No other filesystem is supported.
3. ploop library and tools installed (run yum install ploop).

Making a CT on ploop

Global configuration

In global VZ configuration file /etc/vz/vz.conf, set

VE_LAYOUT=ploop

This means that all new containers you will create will have ploop layout by default.

You don't have to set this option if you don't want ploop to be default. Alternatively, you can:

• use --layout option of vzctl create command;
• convert existing container to ploop.

Creating a new CT

To create a new container on ploop, use:

vzctl create CTID [--layout ploop] [--diskspace nnnG] [--diskinodes mmm]

1. You can omit --layout option if you have set VE_LAYOUT=ploop in vz.conf(5)
2. You can specify initial file system size using --diskspace option (example: 10G for 10 gigabytes)
3. If --diskspace is not specified, the size defaults to DISKSPACE limit value in sample CT config used
4. If --diskinodes is not specified, 1 inode per 16K of disk space will be created (see diskinodes for more info)

Converting an existing CT

1. Stop the container:

vzctl stop CTID

2. Set some sane diskspace value, and reset the diskinodes value. New value for diskspace will be used as a size of newly created ploop image. Here is the example to set diskspace to 10 gigabytes:

vzctl set CTID --diskspace 10G --diskinodes 0 --save

3. Convert:

vzctl convert CTID

4. Once your CT is well tested, you can free disk space by removing files that may have remained from the old container file system in /vz/root/CTID. VERY CAREFULLY (and after testing your converted container) you can stop, remove old files and start container again, e.g.:

vzctl stop CTID
rm -rf /vz/root/CTID;mkdir /vz/root/CTID
vzctl start CTID

Resizing a ploop image

Ploop image can be resized in both directions (i.e. either shrank or grown). Ploop also supports online/live resize so you don't have to stop a CT to do resize.

To resize a ploop CT image, use

vzctl set CTID --diskspace nnnG --save

Note that

• resize can safely be performed online (i.e. when container is running)
• there is no need to specify two values for diskspace (unlike simfs, there is no soft and hard quota).
• there is no way to limit or change the number of inodes available for an existing container (i.e. option --diskinodes is ignored); see diskinodes for more details

Showing disk space usage / limits

You can use vzlist(8) to see CT disk space usage and limits in a uniform way for any containers (simfs or ploop, started or stopped).

The field diskspace is showing the current disk space usage, and the fields diskspace.s and diskspace.h are showing the filesystem size (or disk space quotas, for simfs case).

The field diskinodes is showing the current inodes usage, and the fields diskinodes.s and diskinodes.h are showing the filesystem size (or disk inodes quotas, for simfs case).

Examples:

vzlist -o smart_name,diskspace.h,diskspace

vzlist -o smart_name,diskinodes.h,diskinodes

On a lower level, same info can be obtained via ploop info command:

ploop info /vz/private/501/root.hdd/DiskDescriptor.xml

Using disk quotas inside container

If you want to use standard Linux per-user and per-group disk quota inside a container, you have to enable it using

vzctl set CTID --quotaugidlimit 1000 --save

Note that:

• unlike with simfs, --quotaugidlimit argument can be any non-zero value;
• enabling or disabling in-container disk quotas requires a container restart, so you might find --setmode option helpful.

See vzctl(8) for more details.

See also

• Ploop
• Ploop/backup
• ploop(8)
• vz.conf(5)
• vzctl(8)

</translate>