Difference between revisions of "Setup VzIP on Virtuozzo 7"

From OpenVZ Virtuozzo Containers Wiki
Jump to: navigation, search
(Created page with "{{Virtuozzo}} <translate> <!--T:1--> This article describes how to install Virtuozzo Infrastructure Platform on Virtuozzo 7. == Introduction == You need the following inf...")
 
(Blanked the page)
 
Line 1: Line 1:
−
{{Virtuozzo}}
 
−
<translate>
 
−
<!--T:1-->
 
−
This article describes how to install Virtuozzo Infrastructure Platform on [[Virtuozzo]] 7.
 
−
== Introduction ==
 
  
−
You need the following infrastructure to setup Virtuozzo Infrastructure Platform on Virtuozzo 7:
 
−
# Three controller hosts: physical host or virtual machine with at least 4CPU, 8GB RAM, 150GB disk. These hosts will act as controller and Virtuozzo containers host.
 
−
# Compute hosts: physical host or virtual machine with at least 4CPU, 8GB RAM, 150GB disk.
 
−
# Configured VStorage: a set of
 
−
 
−
== Prerequisites ==
 
−
 
−
You need to install and update your Virtuozzo nodes first. Install Virtuozzo 7 on your controller and compute hosts as usual. You can use basic (local) or Virtuozzo Storage. Update Virtuozzo hosts
 
−
$ yum update -y
 
−
 
−
If you have br0 bridge configured as an IP interface, then you should move an IP address assigned to it to the physical ethernet interface bridged to br0.
 
−
You can check you configuration with the following command:
 
−
 
−
$ if=$(brctl show | grep '^br0' | awk ' { print $4 }') && addr=$(ip addr | grep -w 'br0' | grep inet | awk ' {print $2} ') && gw=$(ip route | grep default | awk ' { print $3 } ') && echo "My interface is '$if', gateway is '$gw', IP address '$addr'"
 
−
 
−
For instance you have the following output after execution the above script:
 
−
 
−
My interface is 'en33', gateway is '192.168.190.2', IP address '192.168.190.134/24'.
 
−
 
−
Then edit your /etc/sysconfig/network-scripts/ifcfg-ens33 to have the following content and remove BRIDGE="br0" string from it:
 
−
...
 
−
ONBOOT=yes
 
−
IPADDR=192.168.190.134
 
−
GATEWAY=192.168.190.2
 
−
PREFIX=24
 
−
...
 
−
 
−
Remove /etc/sysconfig/network-scripts/ifcfg-br0 file.
 
−
 
−
$ rm /etc/sysconfig/network-scripts/ifcfg-br0
 
−
 
−
Then restart network service:
 
−
 
−
$ systemctl restart network
 
−
 
−
== Installing Virtuozzo Infrastructure Platform on [[Virtuozzo]] 7 using packstack ==
 
−
 
−
* Install Virtuozzo Platform Release package to all Virtuozzo OpenStack nodes:
 
−
 
−
$ yum install vz-platform-release
 
−
 
−
* Install packstack package:
 
−
 
−
$ yum install openstack-packstack
 
−
 
−
* Download sample Vz7 packstack answer file:
 
−
 
−
$ wget https://raw.githubusercontent.com/virtuozzo/virtuozzo-openstack-scripts/master/vz7-packstack-ocata.txt
 
−
 
−
* Edit vz7-packstack-ocata.txt enabling/disabling necessary services
 
−
* Replace all references to 'localhost' and '127.0.0.1' host addresses to correct valuses
 
−
* Set all passwords parameters containing PW_PLACEHOLDER string to some meaninful values
 
−
* If you are going to use Virtuozzo Storage as a Cinder Volume backend set the following parameters:
 
−
 
−
  # Enable Virtuozzo Storage
 
−
  CONFIG_VSTORAGE_ENABLED=y
 
−
 
−
  # VStorage cluster name.
 
−
  CONFIG_VSTORAGE_CLUSTER_NAME=
 
−
 
−
  # VStorage cluster password.
 
−
  CONFIG_VSTORAGE_CLUSTER_PASSWORD=
 
−
 
−
  # Bridge mappings
 
−
  CONFIG_NEUTRON_OVS_BRIDGE_MAPPINGS=extnet1:br-ex
 
−
 
−
  # Bridge interfaces
 
−
  CONFIG_NEUTRON_OVS_BRIDGE_IFACES=br-ex:eth0
 
−
 
−
  # Bridge mapping for compute node
 
−
  CONFIG_NEUTRON_OVS_BRIDGES_COMPUTE=extnet1:br-ex
 
−
 
−
* Then run packstack:
 
−
 
−
$ packstack --answer-file=vz7-packstack-ocata.txt
 
−
 
−
== Generate and Upload images == <!--T:18-->
 
−
 
−
* Upload the image to glance:
 
−
 
−
$ glance image-create --name centos7-exe --disk-format ploop --min-ram 512 --min-disk 1 --container-format bare --property vm_mode=exe --property hypervisor_type=vz --property cinder_img_volume_type=vstorage-ploop --file centos7-exe.hds
 
−
 
−
$ glance image-create --name centos7-hvm --disk-format qcow2 --min-ram 1024 --min-disk 10 --container-format bare --property cinder_img_volume_type=vstorage-qcow2 --file CentOS-7-x86_64-GenericCloud.qcow2
 
−
 
−
* CentOS image one can get here [http://cloud.centos.org/centos/7/images/CentOS-7-x86_64-GenericCloud.qcow2 ]
 
−
 
−
== See also == <!--T:100-->
 
−
* [http://docs.openstack.org/newton/install-guide-rdo/nova-controller-install.html Controller Node Installation Guide]
 
−
* [http://docs.openstack.org/newton/install-guide-rdo/nova-compute-install.html Compute Node Installation Guide]
 
−
* [http://docs.openstack.org/newton/install-guide-rdo/environment-packages.html OpenStack Installation Guide]
 
−
* [https://docs.openvz.org/ Virtuozzo Documentation]
 
−
* [[Virtuozzo ecosystem]]
 
−
 
−
</translate>
 
−
 
−
[[Category: HOWTO]]
 

Latest revision as of 15:12, 28 July 2017