Difference between revisions of "Using veth and brctl for protecting HN and saving IP addresses"
Botinki Kira (talk | contribs) m (Robot: Automated text replacement (-VE0 +CT0)) |
|
(No difference)
| |
Revision as of 13:13, 11 March 2008
Configuration described below has been suggested by Ugo123. Appreciates.
Consider we are facing the following task:
1) We have limited range of IP adresses granted by ISP. We want to assign as much granted IPs to containers as possible. We do not want to protect containers from Internet. 2) We want to protect the HN OS (CT0) from Internet and make it possible to manage containers from CT0 within local area network.
Assume we have a HN with 2 ethernet cards (interfaces eth0 and eth1), OpenVZ kernel 2.6.18-028stab033, vzctl version 3.0.16, bridge-utils version 1.1. OpenVZ installation process is covered by http://wiki.openvz.org/Quick_installation.
Task can be effectively solved by setting up the configuration presented on Figure 1.
Figure 1: Effective configuration. 10.0.98.96-10.0.98.X - range of IP-adresses granted by ISP, 192.168.1.136 - IP address from LAN
Initial ifconfig output of HN is the following:
[HN]# ifconfig
eth0 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:34
inet addr:192.168.1.136 Bcast:192.168.3.255 Mask:255.255.252.0
inet6 addr: fe80::230:48ff:fe5b:ab34/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3122 errors:0 dropped:0 overruns:0 frame:0
TX packets:246 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:325879 (318.2 KiB) TX bytes:57278 (55.9 KiB)
Interrupt:20
eth1 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:35
inet addr:192.168.0.32 Bcast:192.168.3.255 Mask:255.255.252.0
inet6 addr: fe80::213:d4ff:fe90:4d50/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:603734 errors:0 dropped:0 overruns:0 frame:0
TX packets:36627 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:21
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1376 errors:0 dropped:0 overruns:0 frame:0
TX packets:1376 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2078718 (1.9 MiB) TX bytes:2078718 (1.9 MiB)
Let us pass through the setup process step by step.
1) Create 2 containers on the HN as described in http://download.openvz.org/doc/OpenVZ-Users-Guide.pdf. For testing purposes I've used opensuse-10 precreated template from openvz.org:
[HN]# cd /vz/template/cache [HN]# wget http://download.openvz.org/template/precreated/opensuse-10-i386-default.tar.gz
Create VE 101 and assign it one of the IP adresses obtained from ISP:
[HN]# vzctl create 101 --ostemplate opensuse-10-i386-default --ipadd 10.0.98.96 [HN]# vzctl set 101 --userpasswd root:XXX --save
And do the same for VE 102 ... VE N. When ready - start containers:
[HN]# vzctl start 101
[HN]# vzlist -a
CTID NPROC STATUS IP_ADDR HOSTNAME
101 4 running 10.0.98.96 -
102 4 running 10.0.98.97 -
2) By default containers use venet device for networking (http://wiki.openvz.org/Venet). But current configuration requires using alternative networking - through veth devices (http://wiki.openvz.org/Virtual_Ethernet_device). Switch VE 101 to veth by doing the following:
MAC address needed by eth0 of VE 101 and veth101.0 should be generated by easymac:
[HN]# wget http://www.easyvmx.com/software/easymac.sh [HN]# chmod 0777 easymac.sh [HN]# ./easymac.sh -R 00:0C:29:70:BB:34 [HN]# ./easymac.sh -R 00:0C:29:C0:2E:07
Replace venet by veth device on HN:
[HN]# ifconfig venet0:0 down [HN]# vzctl set 101 --netif_add eth0,00:0C:29:70:BB:34,veth101.0,00:0C:29:C0:2E:07 --save [HN]# ifconfig veth101.0 0 [HN]# echo 0 > /proc/sys/net/ipv4/conf/veth101.0/forwarding [HN]# echo 0 > /proc/sys/net/ipv4/conf/veth101.0/proxy_arp
Enter VE and tune ifconfig within VE:
[VE 101]# vzctl enter 101 [VE 101]# ifconfig venet0:0 down [VE 101]# ifconfig venet0 down [VE 101]# ifconfig eth0 0 [VE 101]# ip addr add 10.0.98.96 dev eth0 [VE 101]# ip route add default dev eth0
The same (whole item 2) should be done for VE 102 .. VE N. 3) Now we should eliminate the IP address on eth1: [HN]# vim /etc/sysconfig/network-scripts/ifcfg-eth1
Edit like this:
DEVICE=eth1 #BOOTPROTO=dhcp <<== comment HWADDR=XX:XX:XX:XX:XX:XX ONBOOT=yes
and save changes (:wq).
[HN]# /etc/init.d/network restart
And turn off forwarding and proxy_arp for eth1.
[HN]# ifconfig eth1 0 [HN]# echo 0 > /proc/sys/net/ipv4/conf/eth1/forwarding [HN]# echo 0 > /proc/sys/net/ipv4/conf/eth1/proxy_arp
4) Create br0 bridge uniting eth1, veth101.0, ..., vethN.0:
[HN]# brctl addbr br0 [HN]# brctl addif br0 eth1 [HN]# brctl addif br0 veth101.0 ..., veth102.0, vethN.0 etc. [HN]# ifconfig br0 0
And turn off frowarding and proxy_arp for br0:
[HN]# echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding [HN]# echo 0 > /proc/sys/net/ipv4/conf/br0/proxy_arp
This is very important action. If skipped - network can be broken on further steps due to incoming arp-requests provoked storm.
As a result of above listed actions the ifconfig output like the following should be listed:
[HN]# ifconfig
br0 Link encap:Ethernet HWaddr 00:0C:29:A7:A9:D9
inet6 addr: fe80::20c:29ff:fea7:a9d9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:79 errors:0 dropped:0 overruns:0 frame:0
TX packets:17 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2972 (2.9 KiB) TX bytes:4390 (4.2 KiB)
eth0 Link encap:Ethernet HWaddr 00:30:48:5B:AB:34
inet addr:192.168.1.136 Bcast:192.168.3.255 Mask:255.255.252.0
inet6 addr: fe80::230:48ff:fe5b:ab34/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:347855 errors:0 dropped:0 overruns:0 frame:0
TX packets:4778 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:35964081 (34.2 MiB) TX bytes:698801 (682.4 KiB)
Interrupt:20
eth1 Link encap:Ethernet HWaddr 00:30:48:5B:AB:35
inet6 addr: fe80::230:48ff:fe5b:ab35/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:322 errors:0 dropped:0 overruns:0 frame:0
TX packets:182 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:41943 (40.9 KiB) TX bytes:21338 (20.8 KiB)
Interrupt:21
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1376 errors:0 dropped:0 overruns:0 frame:0
TX packets:1376 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2078718 (1.9 MiB) TX bytes:2078718 (1.9 MiB)
veth101.0 Link encap:Ethernet HWaddr 00:0C:29:C0:2E:07
inet6 addr: fe80::20c:29ff:fec0:2e07/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:363 errors:0 dropped:0 overruns:0 frame:0
TX packets:397 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:31134 (30.4 KiB) TX bytes:31440 (30.7 KiB)
veth102.0 Link encap:Ethernet HWaddr 00:0C:29:A7:A9:D9
inet6 addr: fe80::20c:29ff:fea7:a9d9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:36 errors:0 dropped:0 overruns:0 frame:0
TX packets:60 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1840 (1.7 KiB) TX bytes:2350 (2.2 KiB)
5) That is all. It's time to test the obtained configuration. Now plug eth1 of HN into network wall outlet provided by ISP and carry out the following testing:
- It should be tested that containers are accessible from Internet:
[INET]# ssh root@10.0.98.96 [VE 101]# ...
- HN is not accessible from Internet:
[INET]# ssh root@192.168.1.136 inaccessible
- containers can be managed from HN:
[HN]# vzctl enter 101 [VE 101]# ...
- containers VE 101, VE 102 .. VE N "see" each other (ping).
If all the steps are done as written, it should work. Enjoy.
