Multiple network interfaces and ARP flux

Overview

This page discusses how to setup a HN with multiple network interfaces on the same physical network and on the same IP network. Then how to setup multiple VE's to use only one of these interfaces.

For example, you want some of your VE's to always use eth3, and some to use eth4. But none of the VE traffic should use eth0, which is reserved for use by the HN only. This makes sense if you have VE's that may generate or receive a lot of traffic and you don't want your remote administration of the server over eth0 to degrade or get blocked because of this.

To make this clear we'll use the following HN configuration. We'll also have another system to act as the client.

System	Interface	MAC Address	IP Address
HN	eth0	00:0c:29:b3:a2:54	192.168.18.10
HN	eth3	00:0c:29:b3:a2:68	192.168.18.11
HN	eth4	00:0c:29:b3:a2:5e	192.168.18.12
client	eth0	00:0c:29:d2:c7:aa	192.168.18.129

HN ARP Flux

The first issue is ARP flux. Any client on the network broadcasting an ARP "who has" message for any of these addresses will receive replies from all three interfaces. This results in IP addresses that float between three MAC addresses, depending on which response a client accepts first.

For example, the following is a tcpdump capture from executing

ping -c2 192.168.18.10

from another system on the network.

00:0c:29:d2:c7:aa > ff:ff:ff:ff:ff:ff, ARP, length 60: arp who-has 192.168.18.10 tell 192.168.18.129
00:0c:29:b3:a2:5e > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.10 is-at 00:0c:29:b3:a2:5e
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.10 is-at 00:0c:29:b3:a2:54
00:0c:29:b3:a2:68 > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.10 is-at 00:0c:29:b3:a2:68
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:5e, IPv4, length 98: 192.168.18.129 > 192.168.18.10: ICMP echo request, id 32313, seq 1, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, IPv4, length 98: 192.168.18.10 > 192.168.18.129: ICMP echo reply, id 32313, seq 1, length 64
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:5e, IPv4, length 98: 192.168.18.129 > 192.168.18.10: ICMP echo request, id 32313, seq 2, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, IPv4, length 98: 192.168.18.10 > 192.168.18.129: ICMP echo reply, id 32313, seq 2, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, ARP, length 60: arp who-has 192.168.18.129 tell 192.168.18.10
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, ARP, length 60: arp reply 192.168.18.129 is-at 00:0c:29:d2:c7:aa

The ARP "who has" message generated replies from all three MAC addresses on the HN. In this case the client took the MAC address for eth4. The three ICMP messages are then sent to eth4, but all the replies com from eth0. Normally this behavior isn't a problem, though it may generate some false alarms for a network monitor as it appears someone could be executing a man in the middle attack.

The following output is from executing this command on the HN.

sysctl -a | grep net.ipv4.conf.*.arp

net.ipv4.conf.venet0.arp_accept = 0
net.ipv4.conf.venet0.arp_ignore = 0
net.ipv4.conf.venet0.arp_announce = 0
net.ipv4.conf.venet0.arp_filter = 0
net.ipv4.conf.venet0.proxy_arp = 0
net.ipv4.conf.eth4.arp_accept = 0
net.ipv4.conf.eth4.arp_ignore = 0
net.ipv4.conf.eth4.arp_announce = 0
net.ipv4.conf.eth4.arp_filter = 0
net.ipv4.conf.eth4.proxy_arp = 0
net.ipv4.conf.eth3.arp_accept = 0
net.ipv4.conf.eth3.arp_ignore = 0
net.ipv4.conf.eth3.arp_announce = 0
net.ipv4.conf.eth3.arp_filter = 0
net.ipv4.conf.eth3.proxy_arp = 0
net.ipv4.conf.eth0.arp_accept = 0
net.ipv4.conf.eth0.arp_ignore = 0
net.ipv4.conf.eth0.arp_announce = 0
net.ipv4.conf.eth0.arp_filter = 0
net.ipv4.conf.eth0.proxy_arp = 0
net.ipv4.conf.lo.arp_accept = 0
net.ipv4.conf.lo.arp_ignore = 0
net.ipv4.conf.lo.arp_announce = 0
net.ipv4.conf.lo.arp_filter = 0
net.ipv4.conf.lo.proxy_arp = 0
net.ipv4.conf.default.arp_accept = 0
net.ipv4.conf.default.arp_ignore = 0
net.ipv4.conf.default.arp_announce = 0
net.ipv4.conf.default.arp_filter = 0
net.ipv4.conf.default.proxy_arp = 0
net.ipv4.conf.all.arp_accept = 0
net.ipv4.conf.all.arp_ignore = 0
net.ipv4.conf.all.arp_announce = 0
net.ipv4.conf.all.arp_filter = 0
net.ipv4.conf.all.proxy_arp = 0

If all three network interfaces are on different IP networks (such as 10.x.x.x, 172.16.x.x, 192.168.x.x) then executing the following will work:

sysctl -w net.ipv4.conf.all.arp_filter=1

However, if they are all on the same IP network, which is the case here, then the following solution will work. This can be added to your /etc/sysctl.conf file once you've tested it.

sysctl -w net.ipv4.conf.all.arp_ignore=1
sysctl -w net.ipv4.conf.all.arp_announce=2

The following output is from executing this command on the HN.

sysctl -a | grep net.ipv4.conf.*.arp

net.ipv4.conf.venet0.arp_accept = 0
net.ipv4.conf.venet0.arp_ignore = 0
net.ipv4.conf.venet0.arp_announce = 0
net.ipv4.conf.venet0.arp_filter = 0
net.ipv4.conf.venet0.proxy_arp = 0
net.ipv4.conf.eth4.arp_accept = 0
net.ipv4.conf.eth4.arp_ignore = 0
net.ipv4.conf.eth4.arp_announce = 0
net.ipv4.conf.eth4.arp_filter = 0
net.ipv4.conf.eth4.proxy_arp = 0
net.ipv4.conf.eth3.arp_accept = 0
net.ipv4.conf.eth3.arp_ignore = 0
net.ipv4.conf.eth3.arp_announce = 0
net.ipv4.conf.eth3.arp_filter = 0
net.ipv4.conf.eth3.proxy_arp = 0
net.ipv4.conf.eth0.arp_accept = 0
net.ipv4.conf.eth0.arp_ignore = 0
net.ipv4.conf.eth0.arp_announce = 0
net.ipv4.conf.eth0.arp_filter = 0
net.ipv4.conf.eth0.proxy_arp = 0
net.ipv4.conf.lo.arp_accept = 0
net.ipv4.conf.lo.arp_ignore = 0
net.ipv4.conf.lo.arp_announce = 0
net.ipv4.conf.lo.arp_filter = 0
net.ipv4.conf.lo.proxy_arp = 0
net.ipv4.conf.default.arp_accept = 0
net.ipv4.conf.default.arp_ignore = 0
net.ipv4.conf.default.arp_announce = 0
net.ipv4.conf.default.arp_filter = 0
net.ipv4.conf.default.proxy_arp = 0
net.ipv4.conf.all.arp_accept = 0
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 1
net.ipv4.conf.all.arp_filter = 0
net.ipv4.conf.all.proxy_arp = 0

Now we repeat the ping command, after the arp cache has been cleared.

00:0c:29:d2:c7:aa > ff:ff:ff:ff:ff:ff, ARP, length 60: arp who-has 192.168.18.10 tell 192.168.18.129
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.10 is-at 00:0c:29:b3:a2:54
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, IPv4, length 98: 192.168.18.129 > 192.168.18.10: ICMP echo request, id 32066, seq 1, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, IPv4, length 98: 192.168.18.10 > 192.168.18.129: ICMP echo reply, id 32066, seq 1, length 64
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, IPv4, length 98: 192.168.18.129 > 192.168.18.10: ICMP echo request, id 32066, seq 2, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, IPv4, length 98: 192.168.18.10 > 192.168.18.129: ICMP echo reply, id 32066, seq 2, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, ARP, length 60: arp who-has 192.168.18.129 tell 192.168.18.10
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, ARP, length 60: arp reply 192.168.18.129 is-at 00:0c:29:d2:c7:aa

The desired affect has been achieved. Only interface eth0 on the HN responds to the ARP message and the other interfaces are silent.

Adding some VE's

Now let's add some VE's to the HN as follows:

VEID	IP
101	192.168.18.101
102	192.168.18.102

From another system on the network you should be able to ping both. However, looking at the ARP traffic with tcpdump you'll see that once again the physical address associated with each VE will be subject to ARP flux, drifting between all three IP addresses over time.

00:0c:29:d2:c7:aa > ff:ff:ff:ff:ff:ff, ARP, length 60: arp who-has 192.168.18.101 tell 192.168.18.129
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.101 is-at 00:0c:29:b3:a2:54
00:0c:29:b3:a2:68 > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.101 is-at 00:0c:29:b3:a2:68
00:0c:29:b3:a2:5e > 00:0c:29:d2:c7:aa, ARP, length 60: arp reply 192.168.18.101 is-at 00:0c:29:b3:a2:5e
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, IPv4, length 98: 192.168.18.129 > 192.168.18.101: ICMP echo request, id 43311, seq 1, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, IPv4, length 98: 192.168.18.101 > 192.168.18.129: ICMP echo reply, id 43311, seq 1, length 64
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, IPv4, length 98: 192.168.18.129 > 192.168.18.101: ICMP echo request, id 43311, seq 2, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, IPv4, length 98: 192.168.18.101 > 192.168.18.129: ICMP echo reply, id 43311, seq 2, length 64
00:0c:29:b3:a2:54 > 00:0c:29:d2:c7:aa, ARP, length 60: arp who-has 192.168.18.129 tell 192.168.18.10
00:0c:29:d2:c7:aa > 00:0c:29:b3:a2:54, ARP, length 60: arp reply 192.168.18.129 is-at 00:0c:29:d2:c7:aa

The reasons for this can be found from executing the following command on the HN.

arp -an

? (192.168.18.129) at 00:0C:29:D2:C7:AA [ether] on eth0
? (192.168.18.102) at <from_interface> PERM PUB on eth3
? (192.168.18.102) at <from_interface> PERM PUB on eth4
? (192.168.18.102) at <from_interface> PERM PUB on eth0
? (192.168.18.101) at <from_interface> PERM PUB on eth3
? (192.168.18.101) at <from_interface> PERM PUB on eth4
? (192.168.18.101) at <from_interface> PERM PUB on eth0

Another view is obtained from the following command on the HN.

cat /proc/net/arp

IP address       HW type     Flags       HW address            Mask     Device
192.168.18.102   0x1         0xc         00:00:00:00:00:00     *        eth3
192.168.18.102   0x1         0xc         00:00:00:00:00:00     *        eth4
192.168.18.102   0x1         0xc         00:00:00:00:00:00     *        eth0
192.168.18.101   0x1         0xc         00:00:00:00:00:00     *        eth3
192.168.18.101   0x1         0xc         00:00:00:00:00:00     *        eth4
192.168.18.101   0x1         0xc         00:00:00:00:00:00     *        eth0

What this shows is that each VE's IP address is associated with each HN's interface. Therefore each interface will respond to any ARP "who has" query.

TODO: Discuss approach of ip rule ... and ip route ....