1,734
edits
Changes
add category monitoring
</pre>
edit '''/etc/default/snmpd''' : remove ''-u snmp'' and repleace replace ''127.0.0.1'' witch with your ip(ie : 207.46.250.119), Full'''/etc/default/snmpd''' example:
<pre>
export MIBDIRS=/usr/share/snmp/mibs
</pre>
For Debian 4.x:<pre>export MIBDIRS=/usr/share/snmp/mibsSNMPDRUN=yesSNMPDOPTS='-Lsd -Lf /dev/null -I -smux -p /var/run/snmpd.pid'TRAPDRUN=noTRAPDOPTS='-Lsd -p /var/run/snmptrapd.pid'</pre> Create user(my_username) and add new mib. Password need a min. of 8 charactes. Username only characters:
<pre>
/etc/init.d/snmpd stop
echo rouser my_username priv >> /etc/snmp/snmpd.conf
echo "extend .1.3.6.1.4.1.2021.51 beancounters /bin/cat /proc/user_beancounters" >> /etc/snmp/snmpd.conf
echo "extend .1.3.6.1.4.1.2021.52 vzquota /bin/cat /proc/vz/vzquota" >> /etc/snmp/snmpd.conf
echo createUser my_username MD5 my_password DES >> /var/lib/snmp/snmpd.conf
/etc/init.d/snmpd start
</pre>
(Note that the createUser command goes into a separate file. On Centos5 this file is located in /var/net-snmp/snmpd.conf. Make sure you stop snmpd before putting the createUser command there!).
Testing snmp:
<pre>
snmpwalk -v 3 -u my_usrname my_username -l authPriv -a MD5 -A my_password -x DES -X my_password 207.46.250.119$(hostname -i)
</pre>
=== nagios plugin ===
It is shell script:
<presource lang="bash">
# cat /usr/local/bin/check_snmp_openvz.sh
#!/bin/bash
RET=0
DATA_TMP=`snmpwalk -v 3 -u $USER -l authPriv -a MD5 -A $PASS -x DES -X $PASS $HOST:$PORT .1.3.6.1.4.1.2021.51.4`if [ "$?" != "0" ]; then echo "Unknown snmp error" exit 1fi DATA=`echo "$DATA_TMP"| perl -ne '/"(.*)"/ ; print "$1\n" ;'` if [ -f $FILE ]; thenecho "$DATA" | perl -n -e'use Data::Dumper;my $file=$ENV{"FILE"};my $ret=0 ;my $vid ;my $resource ;my $held ;my $maxheld ;my $barrier ;my $limit ;my $failcnt ;my %beancounters ;my %beancounters_old ;while(<STDIN>){ my %vmachine; if ( /\D*(\d+):.*/ ){ $vid=$1; $beancounters{$vid}=\%vmachine ; } if ( /^[\W\d]+([a-z]+)\s+(\d+)\s+(\d+)\s+(\d+)\s+(\d+)\s+(\d+).*/ ) { $resource=$1 ; $held=$2 ; $maxheld=$3 ; $barrier=$4 ; $limit=$5 ; $failcnt=$6 ; ${beancounters{$vid}}{$resource}=[$held , $maxheld , $barrier , $limit ,$failcnt ]; if ( ($held > $barrier) && ($barrier != 0) ) { print "WARNING: Limits on $vid: $resource held->$held , barrier->$barrier ( limit->$limit ) " ; $ret=1; } }} # read and parse old dataopen(MYINPUTFILE, "<$file");while(<MYINPUTFILE>){ my %vmachine; if ( /\D*(\d+):.*/ ){ $vid=$1; $beancounters_old{$vid}=\%vmachine ; } if ( /^[\W\d]+([a-z]+)\s+(\d+)\s+(\d+)\s+(\d+)\s+(\d+)\s+(\d+).*/ ) { $resource=$1 ; $held=$2 ; $maxheld=$3 ; $barrier=$4 ; $limit=$5 ; $failcnt=$6 ; ${beancounters_old{$vid}}{$resource}=[$held , $maxheld , $barrier , $limit ,$failcnt ]; }} foreach my $vmachine_id (keys %beancounters) { foreach my $resource (keys %{$beancounters{$vmachine_id}} ) { if ( defined($beancounters{$vmachine_id}{$resource}[4]) && defined($beancounters_old{$vmachine_id}{$resource}[4]) ){ my $failcnt=$beancounters{$vmachine_id}{$resource}[4]; my $failcnt_old=$beancounters_old{$vmachine_id}{$resource}[4]; my $held=$beancounters{$vmachine_id}{$resource}[0]; my $maxheld=$beancounters{$vmachine_id}{$resource}[1]; my $barrier=$beancounters{$vmachine_id}{$resource}[2]; my $limit=$beancounters{$vmachine_id}{$resource}[3]; if ( $failcnt_old < $failcnt ){ print "CRITICAL: Incrased failcnt $vmachine_id: $resource from $failcnt_old to $failcnt (held->$held , maxheld->$maxheld , barrier->$barrier , limit->$limit ) " ; $ret=2; } } } } # if ($ret == 0 ) { print "Ok. \n" ; }# print Dumper(%beancounters_old) ;# print "\n";exit($ret);' RET1=$?fi echo "$DATA" > $FILE############################################################################################## quota check##################################################################################### DATA=`snmpwalk -v 3 -u $USER -l authPriv -a MD5 -A $PASS -x DES -X $PASS $HOST:$PORT .1.3.6.1.4.1.2021.5152.4 \
| perl -ne '/"(.*)"/ ; print "$1\n" ;'`
echo "Unknown snmp error"
exit 1
fi
echo "$DATA" | perl -n -e'
my $vid ;
my $ret=0 ;
while(<STDIN>){
my %vid;
if ( /\D*(\d+):.*/ ){ $vid=$1; }
if ( /\s*(\S+)\s+(\d+)\s+(\d+)\s+(\d+)\s+(\d+)\s+(\d+).*/ ){
$resource=$1 ;
$usage=$2 ;
$softlimit=$3 ;
$hardlimit=$4 ;
$time=$5 ;
$expire=$6 ;
if ( $usage >= $softlimit ){
print "WARNING: VZquota limit exceeded on $vid: $resource usage->$usage, softlimit->$softlimit, hardlimit->$hardlimit, time->$time, expire->$expire " ;
$ret=1;
}
}
}
exit($ret);
'
RET2=$?
#####################################################################################
########### return
#####################################################################################
if [ $RET1 -gt $RET2 ]; then
RET=$RET1
else
RET=$RET2
fi
if [ $RET = 0 ]; then
echo Ok.
fi
exit $RET
</source>
=== check_vzquota Without SNMP ===
<source lang="bash">
#!/bin/bash
RET=0
DATA=`echo;sudo /usr/sbin/vzlist -1 2>/dev/null | xargs -I {} bash -c "echo {}:;sudo /usr/sbin/vzquota stat {} | sed 's/\*//g'"`
if [ -z "$DATA" ]; then
VPS_err=$(sudo /usr/sbin/vzlist -1 2>&1 1>/dev/null)
if [ -n "$VPS_err" ] && [ "$VPS_err" == "Container(s) not found" ]; then
echo "OK - $VPS_err";
exit 0;
else
if [ -n "$VPS_err" ]; then
echo "UNKNOWN - Error: $VPS_err";
else
echo "UNKNOWN - VZquota stats are not readable or empty. Maybe it is only readable for root and this script should be called by sudo.";
fi
exit 3;
fi
fi
echo "$DATA" | perl -n -e'
my $vid ;
my $ret=0 ;
my $crit="";
my $warn="";
my $ok="";
while(<STDIN>){
my %vid;
if ( /^(\d+):.*/ ){ $vid=$1; }
if ( /\D*(\d+):.*/ ){ $vid=$1; }
if ( /\s*(\S+)\s+(\d+)\s+(\d+)\s+(\d+).*/ ){
$resource=$1 ;
$usage=$2 ;
$softlimit=$3 ;
$hardlimit=$4 ;
if ( $usage >= $hardlimit ){
$crit=$crit."VZquota limit exceeded on $vid: $resource usage->$usage, softlimit->$softlimit, hardlimit->$hardlimit, time->$time, expire->$expire " ;
$ret=2;
} elsif ( $usage >= $softlimit ){
$warn=$warn."VZquota limit exceeded on $vid: $resource usage->$usage, softlimit->$softlimit, hardlimit->$hardlimit, time->$time, expire->$expire " ;
$ret=1;
}
$ok=$ok."$vid:$resource $usage/$softlimit\n";
}
}
if ($ret == 0) {
print "OK - click on service-link for details...\n$ok";
} elsif ($ret == 1) {
print "WARNING - $warn\n";
} else {
print "CRITICAL - $crit\n";
}
exit($ret);
'
RET=$?
exit $RET
</source>
The script calls <code>/usr/sbin/vzlist</code> by sudo. When doing this it normally needs a password, which check_nrpe will not know. Because of this it is necessary that you append a line like the following to <code>/etc/sudors</code> (user name an path should be adapted to the right ones on your system):
nagios ALL=NOPASSWD: /usr/sbin/vzlist, /usr/sbin/vzquota
=== check_ubc Without SNMP ===
<source lang="bash">
#!/bin/bash
# Servicestate description can have a http-link to the openvz-wiki
# in case that a ressource is warning/critical. To use it:
# 1. set "escape_html_tags=0" in nagios/etc/cgi.cfg
# 2. set "my $linked=1;" in the first perl lines in this script
#
export FILE=/tmp/check_ubc
RET=0
ubc_file='/proc/user_beancounters';
DATA='';
if [ -r $ubc_file ]; then
DATA=`cat $ubc_file`
fi
if [ -z "$DATA" ]; then
echo "UNKNOWN - $ubc_file is not readable or empty. Maybe it is only readable for root and this script should be called by sudo.";
exit 3;
fi
echo "$DATA" | perl -n -e'
use Data::Dumper;
my $linked=1; # 0:plain text output, 1:resourcename is a http-link to OpenVZ-wiki
my $file=$ENV{"FILE"};
my $ret=0 ;
${beancounters{$vid}}{$resource}=[$held , $maxheld , $barrier , $limit ,$failcnt ];
if ( ($held > $barrier) && ($barrier != 0) ) {
print "WARNING: Limits on $vid: ".&url($resource ,$linked)." held->$held , barrier->$barrier ( limit->$limit ) \n" ;
$ret=1;
}
#print "$vid:$resource $held Barrier:$barrier ";
}
}
my $limit=$beancounters{$vmachine_id}{$resource}[3];
if ( $failcnt_old < $failcnt ){
print "CRITICAL: Incrased Increased failcnt $vmachine_id: ".url($resource ,$linked)." from $failcnt_old to $failcnt (held->$held , maxheld->$maxheld , barrier->$barrier , limit->$limit ) \n" ;
$ret=2;
}
#print "$vmachine_id: Old_Failcnt: $failcnt_old Failcnt: $failcnt \n";
}
}
}
sub url { my ($name,$with_link) = @_; if ($with_link) { return "<a target=\"_blank\" href=\"http://wiki.openvz.org/".$name."#".$name."\">$name</a>"; } else { return $name; }}if ($ret == 0 ) { print "Ok. OK: All bean counters fine \n" ; }
# print Dumper(%beancounters_old) ;
# print "\n";
exit($ret);
'
echo "$DATA" > $FILE
exit $RET
</source>
The script needs to read the <code>/proc/user_beancounters</code> file. This is normally only readable for root. Because of this it is necessary that you append a line like the following to <code>/etc/sudors</code> (user name an path should be adapted to the right ones on your system):
nagios ALL=NOPASSWD: /usr/local/nagios/libexec/check_ubc
Also don't forget to consider this on your <code>nrpe.cfg</code>, so that you call the script with sudo:
command[check_ubc]=sudo /usr/local/nagios/libexec/check_ubc