User pages accounting

User Beancounters Definition /proc/user_beancounters /proc/bc/ General information Units of measurement VSwap Parameters description Primary parameters numproc, numtcpsock, numothersock, vmguarpages Secondary parameters kmemsize, tcpsndbuf, tcprcvbuf, othersockbuf, dgramrcvbuf, oomguarpages, privvmpages Auxiliary parameters lockedpages, shmpages, physpages, numfile, numflock, numpty, numsiginfo, dcachesize, numiptent, swappages Internals User pages accounting RSS fractions accounting On-demand accounting UBC consistency Consistency formulae System-wide configuration vzubc(8) Configuration examples Basic Derived Intermediate configurations Tables List of parameters Parameter properties Consistency Config examples

This article describes internals of user-space pages accounting.

Contents

IntroductionEdit

User pages is the second important resource (after kmemsize) which must be accounted. Unlike kernel memory, which is either used or not, the set of user pages may have different classifications. Pages may be backed by file, locked, unused, i.e. requested with mmap/brk but not yet touched and so on. Thus user pages accounting is trickier than the one for kernel pages.

Ways of accountingEdit

There are different approaches to user pages control:

Account all the mappings on mmap/brk and reject as soon as the sum of VMA's lengths reaches the barrier.

This approach is very bad as applications always map more than they really use, very often MUCH more.

Account only the really used memory and reject as soon as RSS reaches the limit.

This approach is not good either as the only place where pages appear in user space is page fault handler and the only way to reject is killing the task. Comparing to previous scenarion this is much worse as application won't even be able to terminate gracefully.

Account a part of memory on mmap/brk and reject there, and account the rest of the memory in page fault handlers without any rejects.

This type of accounting is used in UBC.

Account physical memory and behave like a standalone kernel - reclaim user memory when run out of it.

This type of memory control is to be introduced later as an addition to current scheme. UBC provides all the needed statistics for this (physical memory, swap pages etc.)

UBC user pages accountingEdit

TermsEdit

The following terms are used by UBC:

• shmem mapping — a mapping of file belonging to tmpfs. UBC accounts these pages separately and the description below doesn't take such pages into account;
• private mapping — this includes the following types of mappings:
  • writable anonymous mappings
  • writable private file mappings

Both types are not backed by disk file and thus may not be just freed. These mappings are charged with possible reject right when they are made — in sys_mmap()/sys_brk().

• unused pages — this is the number of pages which belong to private mapping, but are not yet touched.

Math modelEdit

The following notations are used:

• $UB_{privvm}$ is the total number of privvmpages accounted on UB. In other words, this is the value seen in /proc/user_beancounters in privvmpages.held;
• $UB_{unused}$ is the total number of unused pages. This parameter is shown in /proc/user_beancounters_debug file;
• $Frac(page,UB)$ is some value that represents the part of the page charged to beancounter in case when page is mapped;
• $RSS$ is the amount of physical memory used by processes.

Page fraction — $Frac(page,UB)$ — normally should be ${\frac {1}{N}}$, where $N$ is the number of UBs the pages are shared between, but this is bad since adding a new UB to page shared set would require recalculation of the whole current set. In UB $Frac(page,UB)={\frac {1}{2^{UB_{shift}}}}$, where $UB_{shift}$ is some parameter which is calculated so that

$\sum _{UB:page\in UB}Frac(page,UB)=1,\forall page$.

The notation $page\in UB$ means “there exists an mm_struct, where the page $page$ is mapped to and this mm_struct belongs to $UB$ beancounter”. This type of calculation allows making an O(1) algorithm of fractions accounting.

Privvmpages accounts the sum of unused pages and the “normalized” number of RSS pages:

$UB_{privvm}=UB_{unused}+\sum _{page\in UB}Frac(page,UB)$

If you sum the privvmpages of all beancounters in the system you'll get an upper estimation of current physical memory usage by processes:

$\sum _{UB}UB_{privvm}=\,$

$\sum _{UB}UB_{unused}+\sum _{UB}{\sum _{page\in UB}Frac(page,UB)}=$

$\sum _{UB}UB_{unused}+\sum _{page}\sum _{UB:page\in UB}Frac(page,UB)=$

$\sum _{page:page\ is\ mapped}1+\sum _{UB}UB_{unused}=$

$RSS+\sum _{UB}UB_{unused}\,$

To get real physical memory usage physpages resource is used .

$UB_{physpages}=\sum _{page\in UB}Frac(page,UB)$

Thus

$\sum _{UB}UB_{physpages}=RSS\,$

---