Man/vzmigrate.8
NAME
vzmigrate − migrate a container between two OpenVZ servers
SYNOPSIS
|
vzmigrate |
[-r|--remove-area yes|no] [--ssh=ssh_options] [--rsync=rsync_options] [--keep-dst] [--live] [-c|--compact] [-s|--snapshot] [--check-only|--dry-run] [-t|--times] [-v] destination_address CTID |
DESCRIPTION
This utility is used to migrate a container from one (source) Hardware Node (HN) to another (destination) HN. The utility can migrate either stopped or running container. For a stopped container, simple CT private area transfer is performed (rsync(1) is used for file transfer). For running containers, either traditional (with CT stop and start) or live migration is possible.
This program uses ssh as a transport layer. You will need to put ssh public key to destination node and be able to connect to node without entering password.
OPTIONS
-r, --remove-area yes | no
Whether to remove a container area on source HN for the successfully migrated container. Default is yes.
--ssh=options
Additional options that will be passed to ssh while establishing connection to destination HN.
--rsync=options
Additional options that will be passed to rsync(8). You may add options like -z to enable data compression if you are migrating over a slow link.
--keep-dst
Do not clean synced destination container private area in case of some error. It makes sense to use this option on big container migration to avoid syncing container private area again in case some error (on container stop for example) occurs during first migration attempt.
|
--live |
--live Perform live migration: instead of restarting a container, checkpoint and restore are used, so there is no container downtime or service interruption. Additional steps are performed to minimize the time when a container is in suspended state. Option --online can be used as a backward-compatible alias. |
-c, --compact
Compact a container image (i.e. run vzctl compact) before migration. Works for ploop only, ignored otherwise.
-s, --snapshot
Create a container snapshot (i.e. run vzctl snapshot) before migration. Works for ploop only, ignored otherwise.
--check-only, --dry-run
Do not perform actual migration, stop after preliminary checks. This is used to check if a CT can possibly be migrated. Combine with --live to enable more checks for live migration case.
-t, --times
At the end of live migration, output various timings for migration stages that affect total suspended CT time. Note that it only makes sense with --live.
|
-v |
Verbose mode. Causes vzmigrate to print debugging messages about its progress. Note that -v automatically implies -t. Multiple -v options increase the verbosity. |
EXAMPLES
Migration of CT 101 to 192.168.1.130 with downtime:
vzmigrate 192.168.1.130 101
Online migration of CT 102 to 192.168.1.130:
vzmigrate --live 192.168.1.130 102
EXIT STATUS
0 EXIT_OK
Command completed successfully.
1 EXIT_USAGE
Bad command line options.
2 EXIT_VE_STOPPED
Container is stopped.
4 EXIT_CONNECT
Can’t connect to destination (source) HN.
6 EXIT_COPY
Container private area copying/moving failed.
7 EXIT_VE_START
Can’t start or restore destination CT.
8 EXIT_VE_STOP
Can’t stop or checkpoint source CT.
9 EXIT_EXISTS
Container already exists on destination HN.
10 EXIT_NOTEXIST
Container does not exists on source HN.
12 EXIT_IP_INUSE
You attempt to migrate CT which IP address(es) are already in use on the destination node.
13 EXIT_QUOTA
Operation with CT quota failed.
14 EXIT_OVZ_NOT_RUNNING
OpenVZ is not running, or some required kernel modules are not loaded.
15 EXIT_APPLY_CONFIG
Unable to set CT name on destination node.
16 EXIT_PLOOP_UNSUP
Ploop is not supported by destination node.
17 EXIT_UNSUP_CPT_VER
CPT version incompatibility with the destination node.
18 EXIT_UNSUP_CPU
Destination node CPU incompatibility.
SEE ALSO
rsync(1), vzcptcheck(8).
COPYRIGHT
Copyright (C) 2001-2013, Parallels, Inc. Licensed under GNU GPL.
